| Pos.01 | SCN KNX Modbus Gateway RTU485. |
|---|---|
 SCN-MBGRTU 
|
Description: Designed for bidirectional Data exchange between Modbus RTU- and KNX-products.
| Data Sheet | Technical Manual | |
| Pos.01 | SCN Time Switch 20-channel with LCD display. |
 SCN-RTC20 |
Description: The MDT Time Switch with 20 channels (8 cycle times for each channel) has a daily/weekly/astro switching function and an adequate power reserve if the bus voltage fails. The cycle times of the single channels are adjustable by the ETS or can be set directly at the device. The large active color display for comfortable handling allows direct switching of the 20 channels (Manual Mode).
| Data Sheet | Technical Manual | |
| Pos.02 | SCN Logic Module MDRC device. |
 SCN-LOG1 |
Description: The MDT Logic Module is used for fast and easy compilation of logic functions to control building automation systems. All the functions are parametrized directly in the ETS without additionally software tools. There are 24 independent function blocks with arbitrary functions available. For each function a description can be stored in the ETS. The 4 LEDs on the front panel can be controlled optional by objects. According to date, time and location the Logic Module calculates sunset, sunrise and twilight. Additionally there are output objects available for summer/winter time, day of the week, every hour, every minute, day/night.
| Data Sheet | |
| Pos.03 | SCN USB Interface, SCN Line Coupler, IP Interface/Router. |
 SCN-USBR
|
Description: USB Interface enables the communication between the PC and the KNX / EIB system. The USB interface is galvanically isolated from the KNX / EIB bus.
| Data Sheet USBR | KNX IP Line Coupler: KNX Line Coupler: This Interface connects two KNX lines to each other. Electrical isolation between the lines and reduction of the busload by using the filter function.
| Data Sheet USBR | KNX IP Interface: The IP Interface enables the communication between the PC and the KNX/EIB system via LAN. The KNX IP Interface allows to programm the KNX bus via TCP/IP, 4 simultaneous connections possible. KNX IP Router: This Interface offers the same functions as the IP interface, but the device routes telegrams as a line coupler using the the LAN.
| Data Sheet USBR | |
| Pos.04 | SCN Weather Station Home. |
 SCN-WS3HW |
Description: The MDT Weather station Home is made for the weather detection for private use. The installation is made in the outdoor area and should be made on a pole. Alternative, the weather station can be installed on a wall at the southern side. The connection to the bus is made via a 5m long bus cable, which is included in the delivery contents.
Three brightness sensors are included in the weather station, which are faced to the sky directions East, West and South (Have a look at the mounting direction – south). These can be controlled via two threshold values and an extensive facade controlling unit for shutter and blinds. Additional a twilight sensor is integrated. Via an individually adjustable wind sensor, the wind speed can be captured and actions can be performed. The temperature sensor, which can be adjusted with threshold values, complete the service portfolio of the weather station.
| Data Sheet | Technical Manual | |
| Pos.05 | SCN Rain Sensor. |
 SCN-RS1R1 |
Description: The Rain Sensor SCN-RS1R1.01 is used for the detection of rain and send messages if rain was detected. For faster drying after rain and at low temperatures, a heating is integrated below the sensor area. This enables also the detection of two contiguous rain periods.
| Data Sheet | |
| Pos.06 | SCN Twilight/Temperature Sensor. |
 SCN-DTSEN1.01 |
Description: Twilight Sensor/Temperature Sensor KNX for detection and evaluation of outdoor brightness and outdoor temperature with integrated bus coupler.
| Data Sheet | Technical Manual | |
| Pos.07 | SCN Leakage Sensor. |
 SCN-LSEN1.01 |
Description: Leakage sensor for detecting water leakage, with integrated Bus coupler unit.
| Data Sheet | Technical Manual | |
| Pos.08 | SCN CO2/VOC Combi Sensor 55. |
 SCN-CO2MGS  SCN-CO2MGS06 |
Description: The MDT CO2/VOC Combi Sensor 55 has two sensors for measuring the CO2 and mixed gas concentration (VOC). Aside from the measuring channels for CO2 and VOC, the Combi Sensor also records the room temperature and relative humidity. It uses these measured values to carry out temperature and air quality controls. The air quality traffic light gives early warning of excessive CO2 or VOC concentrations in the room.
| Data Sheet | Technical Manual | |
| Pos.09 | SCN Safe Module. |
 SCN-SAFE |
Description: The new MDT security module prevents all connection-oriented accesses of the ETS, such as the programming and also the unloading of the bus devices, in the KNX line. This significantly increases the safety of the protected line in the inner and in the outdoor area. A manipulation of the device programming is no longer possible. The safety function is started automatically after bus voltage recovery/programming of the safety module. The deactivation of the safety function is possible depending on the set safety level via the control buttons on the device and/or with the safety password via telegramm. The integrated device monitoring system controls up to 100 KNX devices cyclically. As soon as a device is missing or no longer responds due to a defect, an alarm message is sent.
| Data Sheet | |
| Pos.10 | Energy Meter EZ with transformer meas & with direct measurement |
 EZ-0363
|
Description: The MDT Energy Meter EZ measures both energy consumption and energy generation (from a photovoltaic system, for example). Aside from simple current and active power measurement, it counts the consumption costs and yields of the generated energy via main and intermediate meters.
|
| Pos.11 | SCN Brightness Sensor/Controller. |
 SCN-LSD01 |
Description: The Brightness Sensor/Controller with constant level light intensity is suited for ceiling installation in 35mm Kaiser installation box.
| Data Sheet | Technical Manual | |
SCN-MBGRTU KNX Modbus Gateway RTU485.
